Tools

No tools required.

Parts

No parts required.

X-Motor Plate
  • X-Motor Plate

  • M3x8 Cap Screws (6 Pcs)

  • M3 Washers (6 Pcs)

  • GT2 Pulley, 16 teeth

  • Standoff M3x23, Female-Female (2 Pcs)

  • X-Motor

Add Comment

Sharp Nose Pliers
  • Sharp Nose Pliers

  • Pratley Pratlock

  • 2.5mm Allen Key

  • 1.5mm Allen Key

Add Comment

  • Place the X-Motor on the table with the wires facing away to the top

  • Place the X-Motor Plate on top of the X-Motor with the slot on the top left corner

  • Mount the plate to the motor with the M3x8 cap screws (4 Pcs), M3 Washers (4 Pcs) and Pratley Pratlock

  • Faster these screws with the 2.5mm Allen Key

Add Comment

  • Slide the GT2 pulley onto the motor shaft with the bigger flanch facing the motor

  • Add Pratley Pratlock to the grub screws

  • Tighten the grub screws with the 1.5mm Allen Key

Add Comment

  • Mount the M3x23 standoffs (2 Pcs) to the X-Motor Plate with the M3x8 cap screws (2 Pcs), M3 Washers (2 Pcs) and Pratley Pratlock

  • Tighten the screws with the 2.5mm Allen Key while holding the standoff with the sharp nose pliers

Add Comment

  • Z-Axis Plate

  • X-Motor Assembly

  • X Drag chain motor bracket

  • V-wheel kit (4 Pcs)

  • Nuts & Bolts (See next step)

Add Comment

  • M4x16 Cap Screw

  • M4 Washer

  • M4 Nut

  • M5 Washer (4 Pcs)

  • Eccentric Nut (2 Pcs)

  • M3x8 Cap Screw (2 Pcs)

  • M3 Washer (2 Pcs)

  • M5x40 Cap Screw (2 Pcs)

Add Comment

  • No. 8 Spanner

  • No. 10 Spanner

  • 2.5mm Allen Key

  • 3mm Allen Key

  • 4mm Allen Key

  • Pratley Pratlock

Add Comment

  • Insert the M4 nut into the slot in the printed Drag Chain Motor Bracket

  • Mount the bracket with the M4x16 cap screw, M4 washer and Pratley Pratlock to the motor plate as shown

Add Comment

  • Mount the V-wheels (2 Pcs) to the holes as indicated with the Eccentric nuts (2 Pcs)

  • Make sure the notch in the Eccentric nuts are pointing downwards

  • Use the No. 8 Spanner and 3mm Allen Key to tighten the V-Wheels

  • Make sure the V-wheels can turn easily

Add Comment

  • Mount the other two V-Wheels between the Z-Axis Plate and the X-Motor Plate with the M5x40 screws (2 Pcs)

  • Use the aluminium spacers that was left over from the first two V-Wheels to mount aluminium spacers on both sides

  • The order of components on the M5x40 screw are: M5 Washer, Z-Axis plate, Aluminium spacer, V-wheel Assembly, Aluminium spacer, X-Motor Plate, M5 Washer, M5 Lock nut

  • After tightening, make sure the V-Wheels can turn easily

Add Comment

  • Fix the loose end of the M3x23 standoffs with the M3x8 cap screws (2 Pcs), M3 Washers (2 Pcs) and Pratley Pratlock

Add Comment

Finish Line

4 other people completed this guide.

Paul Cronje

Member since: 09/03/2017

2,081 Reputation

28 Guides authored

0 Comments

Add Comment