Assemble Components: motherboard, CPU, heatsink, and memory sticks
  • Assemble Components: motherboard, CPU, heatsink, and memory sticks

  • Jumpers - Remove any hanging jumpers. Hanging jumpers are attached to only one (1) pin.

  • Remove the CPU socket cover. Push down on the locking lever and pull it out to the side to release load plate.

Add Comment

Set the CPU down in the socket, taking note of the orientation. Move the load plate over the CPU and secure the locking lever.
  • Set the CPU down in the socket, taking note of the orientation.

  • Move the load plate over the CPU and secure the locking lever.

Add Comment

Populate the BLACK DIMMs, NOT BLUE, with memory sticks. Break off the rear portion of the riser. Install the riser in the "SLOT6 PCI-E 2.0 X8" slot.
  • Populate the BLACK DIMMs, NOT BLUE, with memory sticks.

  • Break off the rear portion of the riser.

  • Install the riser in the "SLOT6 PCI-E 2.0 X8" slot.

Add Comment

Place the heatsink retention bracket underneath the motherboard, lining it up with the holes in the motherboard. Place the heatsink on top of the CPU and fasten it to the retention bracket.
  • Place the heatsink retention bracket underneath the motherboard, lining it up with the holes in the motherboard.

  • Place the heatsink on top of the CPU and fasten it to the retention bracket.

  • NOTE: Be sure the heatsink is not mounted on top of any capacitors and is making full contact with the CPU.

Add Comment

Assemble Components: hard drive, SATA cable, and SATA power adapter.
  • Assemble Components: hard drive, SATA cable, and SATA power adapter.

  • Label the SATA cable 0. Label it on both sides and on both ends.

  • Connect the SATA cable to the hard drive.

  • Remove any hard drive jumpers if necessary.

Add Comment

Remove all of the trash from the accessory box. (Cardboard, Empty Packaging)
  • Remove all of the trash from the accessory box. (Cardboard, Empty Packaging)

  • Sort out needed parts for installation. (Screws, Stand-Offs)

Add Comment

Check to see that all external chassis screws are torqued using a torque screwdriver.
  • Check to see that all external chassis screws are torqued using a torque screwdriver.

  • Replace any stripped screws.

  • Remove any miscellaneous items and place them in the accessory box to be passed onto the next Work Center, these items include airflow guides, deflectors fans, etc.

  • Temporarily remove the mylar sheet and the left/right black plastic air guides.

Add Comment

Ensure that stand-offs are installed in all the circled locations and remove any that are not circled. Place the mylar sheet back into the chassis. Remove the two (2) highlighted NIC port tabs from the I/O shield.
  • Ensure that stand-offs are installed in all the circled locations and remove any that are not circled.

  • Place the mylar sheet back into the chassis.

  • Remove the two (2) highlighted NIC port tabs from the I/O shield.

Add Comment

Check to see that all internal chassis screws are torqued using a torque screwdriver. The highlighted stand-off will be covered by the motherboard, this is OKAY. There is an area on the underside of the motherboard, by this stand-off, that is clear of traces and solder points. Place the assembled motherboard into the chassis.
  • Check to see that all internal chassis screws are torqued using a torque screwdriver.

  • The highlighted stand-off will be covered by the motherboard, this is OKAY. There is an area on the underside of the motherboard, by this stand-off, that is clear of traces and solder points.

  • Place the assembled motherboard into the chassis.

    • Secure the assembled motherboard to the chassis using seven (7) "A" screws.

Add Comment

Connect the longer SATA power cable from the power supply to the hard drive. Place the assembled hard drive into the chassis. Secure the assembled hard drive to the chassis (from the underside) using four (4) "B" screws.
  • Connect the longer SATA power cable from the power supply to the hard drive.

  • Place the assembled hard drive into the chassis.

  • Secure the assembled hard drive to the chassis (from the underside) using four (4) "B" screws.

Add Comment

Reinstall the black plastic air blocker by the hard drive. Route the SATA power cable in front of the fan bracket.
  • Reinstall the black plastic air blocker by the hard drive. Route the SATA power cable in front of the fan bracket.

Add Comment

Apply the serial label, that was retrieved earlier, to the rear of the chassis.
  • Apply the serial label, that was retrieved earlier, to the rear of the chassis.

Add Comment

Click the Finish button in the builder view.
  • Click the Finish button in the builder view.

  • Scan the serial barcode of the system.

  • Click Finish to finish the build.

  • Click Close to exit the popup overlay.

  • Place all unused components into the accessory box or bin.

  • Move the system to the appropriate rack.

  • Pre-Assembly Complete.

Add Comment

Finish Line

Dozuki System

Member since: 09/24/2009

1 Reputation

122 Guides authored

0 Comments

Add Comment